1、 Correct installation of meat grinder power supply: for the correct installation of meat cutter, ensure that the power supply voltage is within the normal range before starting up. First, open the hopper and take out the loose parts from the hopper mouth. Remove the mouth ring, grate, knife and knife shaft. Turn on the power, the bobbin of the meat cutter, press the switch, and see whether the rotating cylinder bottom of the output shaft rotates clockwise. If yes, it indicates the correct installation. On the contrary, error. Replace the power phase sequence. The M6 screw M8 below or the "equipotential live terminal" of the machine shall be carried out by a professional electrician according to the provisions of the ground. The grounding hole of the power socket or the power line of the equipment shall be grounded firmly, green and yellow. The fixed line must be equipped with full pole disconnection, and the cutting distance of contactor is greater than or equal to 3mm.

二、如何正确安装刀轴，刀箅等配件时，扭轴的旋转方向是否正确，将铰链轴，刀，炉排，口环的安装。安装铰链轴，它应该在同一输出轴安装长楔尾长槽;刀片朝前安装在铰链轴在轴的前端;在轴的前端上的铰链轴安装也炉排，与销与一个好的上部环的筒口，旋转。口环又紧了回半扣到适当的水平，前肉类开始机器的正常运转。

2、 How to correctly install knife shaft, knife grate and other accessories, whether the rotation direction of torsion shaft is correct, and the installation of hinge shaft, knife, grate and mouth ring. Install the hinge shaft, which should be installed with long wedge tail and long groove on the same output shaft; The blade is installed on the front end of the hinge shaft facing forward; The hinge shaft on the front end of the shaft is also installed on the grate, rotating with the pin and the barrel mouth of a good upper ring. The mouth ring is tightened again and half buckled back to the appropriate level, and the front meat starts the normal operation of the machine.

三、如何调整弹性机三角带的使用，如三角皮带过松或过紧的发现，应该停止。垂直切肉机开着儒家的电箱下，松开螺母来调整电机的位置，适当调整，然后锁紧螺母可以使用桌面切肉机;打开机箱，松开螺母，调整螺栓后，螺母锁紧。

3、 How to adjust the use of elastic machine V-belt? If the V-belt is too loose or too tight, it should be stopped first. When the vertical meat cutter is under the open electric box, loosen the nut to adjust the position of the motor, and then lock the nut to use the desktop meat cutter; Open the chassis, loosen the nut, and lock the nut after adjusting the bolt.

四、如何清洗机不得直接用水冲洗!不能使电水分!为了避免漏电，触电或使用的影响。拧下口应环，拆下炉排，一把刀和一个铰链轴，清洗后重新加载，以备下次使用。

4、 How to clean the machine? Do not wash it with water directly! You can't make electricity wet! In order to avoid the influence of electric leakage, electric shock or use. Unscrew the mouth ring, remove the grate, a knife and a hinge shaft, clean and reload it for next use.

肉机操作流程

Meat machine operation process

大肉去骨头，并且改刀成进品条状或块状，插好电源，装好刀片，启动机器，注切刀片应向内旋转，把肉块放进去后耐心等待，把切好的肉片拿走或装盘。zui后关闭切肉机并进行清洗，处理。

Remove the bones from the meat, and change the knife into the incoming strip or block, plug in the power supply, install the blade, start the machine, note that the cutting blade should rotate inward, wait patiently after putting the meat in, and take away the cut meat or put it on the plate. After Zui, turn off the meat chopper, wash, sterilize and disinfect it.

切肉机的清洗要看您切肉机的材质，如果您的是不锈钢材质的切肉机，您可以用水进行洗涤就可以了，清洗前拆开切肉的刀片一面早上刮伤。清洗完之后吹干在进行使用这样才能更好的保证清理到位。

The cleaning of the meat chopper depends on the material of your meat chopper. If your meat chopper is made of stainless steel, you can wash it with water. One side of the meat chopper blade is scratched in the morning before cleaning. After cleaning, blow dry before use, so as to better ensure that the cleaning is in place.